Several basic functions and technical indicators that a solid-state fermentation tank must have: Equipped with a temperature sensor of 0-130, which can be adjusted and maintained at a constant temperature within its temperature range and displayed. Some materials will become balls or very viscous after high-pressure steam sterilization, and then stir them into a dough shape, which changes the structure of the materials and can no longer be fermented. Fertilizer production, biogas fermentation tank, production of solid fertilizer.

Sterile water spray (mist) device; It is processed from biological materials, animal and plant wastes, and plant residues to eliminate them. Sterile exhaust device; Speed-regulating fans and pipes; Water evaporation device;  Toxic and harmful substances, rich in a large number of beneficial substances, including: a variety of organic acids, peptides, and rich nutrients including nitrogen, phosphorus, and potassium..

Mix all kinds of organic materials evenly, adjust the water ratio, while stirring, spray the cultured bacteria liquid evenly in the organic materials, adjust the humidity to about 45%-60% (hand knead into a ball without dripping, and loosen it. Stirring The stirring method is the key to the fermentation effect and the success of the fermentation. Sterile filtration device; 3. 5-10 tons of organic materials need to use 1 kilogram of agriculturally transported biological agents each time, and the best effect is to use 2 times of complete compost.

There is a stirrer in the middle, and the stirrer is made of stainless steel welding. It not only provides comprehensive nutrition for crops, but also has long fertilizer efficiency, which can increase and renew soil organic matter, promote microbial reproduction, and improve soil physical and chemical properties and biological activity.

There are two types of vertical and horizontal tanks. The production of fermentation tanks is similar to other fermentation tanks, and China brewery control cabinet system factory they are all made of stainless steel. Mix various organic materials evenly with water as needed

Megosztás a facebookon

Homogenization, degassing, homogenization is to split the suspended pulp particles of the Wholesale micro brewery designs company juice into smaller particles and evenly disperse them in the juice, increase the stability of the juice and prevent delamination. Raw material pretreatment .Fourth, the flavor adjustment of the beverage production line The fruit pulp after the previous treatment needs to be adjusted in order to increase the flavor. Nitrogen exchange method. Among them, nitrogen can cause oxidation of vitamin C and pigments and corrosion of tinplate cans.

Use a half-dig nuclear machine. After cleaning, rinse them in 1% hydrochloric acid solution or detergent solution to remove residual pesticides, then rinse in clean water and drain. The method of homogenization is to pass the coarsely filtered juice through a high-pressure homogenizer, so that the pulp particles and colloidal substances in the juice pass through small holes with a diameter of 0. The straightness of the straight-space method is 685-711 mmHg or more, and the temperature is lower than 43°C.

The juice flows from the top of an upright glass tube or stainless steel tube, and nitrogen is pressed in from the bottom of the tube. Heat the sterilized and canned juice to 95°C for 1 minute, and immediately fill it while it is hot. In addition, a colloid mill can be used for homogenization. There are two main methods for degassing: Vacuum method. The raw material after halving and digging the core is put in . Tighten the cap, and turn the can upside down for one minute. When the juice flows through the slits with a gap of . Cut in half and remove the core. The fruit enters oxygen, nitrogen, carbon dioxide and other gases during juice extraction. Add sugar, citric acid, L-ascorbic acid and other ingredients when adjusting.

Generally, homogenizers of 130-160 kg/cm² are used in production.003 mm under high pressure to become finer particles.45 kilograms of citric acid. After selecting the raw materials, rinse them with clean water to remove the hairs. Soak and protect the color.The finished fruit tea of ​​qualified quality is pink or yellowish brown, and dark red is allowed; the juice is uniformly turbid, and particles precipitate after long-term standing; it has the flavor of peach juice without peculiar smell; the soluble solid content is 10%-14%.The ratio is 100 kilograms of peach pulp, 80 kilograms of 27% sugar solution

After nitrogen is added, numerous small bubbles are formed in the juice, which replace the oxygen in the juice to achieve the purpose of degassing. Therefore, it must be degassed.2 kilograms of L-ascorbic acid. Sealing and cooling of the beverage production line.1%.5 mm to remove the peel.075 mm in the colloid mill, the pulp particles in the juice are impacted and rubbed against each other due to strong centrifugal force, so as to achieve the goal of homogenization.

The raw materials are fully ripe, fresh, good flavor, rich in juice, and free from diseases and insect pests. Heat the berry block at 90℃-95℃, heat it for 3-5 minutes to promote softening, beating through a beater with an aperture of 0. Put the juice into a vacuum container, and make the juice spray out in a misty state for degassing. After sealing, it is quickly cooled in sections to about 38°C, and then stored in the warehouse. Soak the color in a mixed solution of ascorbic acid and citric acid. Cleaning. Peach fruits with insufficient maturity should be post-ripened

Megosztás a facebookon